STARTER ASSEMBLY, 12V

Cross Reference Reference only: Please verify the product is eligible for your aircraft before adding to your cart. OEM Part Number McFarlane Part Number Comment ERZ-8011 149NL 149-NL 149NL 31B23592 149NL

Approval: FAA PMA SupersedesPartNumber: ERZ-8011 (Manufacturer: Hartzell) SupersedesPartNumber: 149-NL (Manufacturer: Hartzell) SupersedesPartNumber: 31B23592 (Manufacturer: Hartzell)

In some cases, engine kickback will fracture starter drive gears. Kickback is related to engine set up and can be anything from incorrect timing to problems with the fuel system. If kickback is noticed as a common occurrence on the airplane, diagnose and repair the problem or the replaced starter drive may fracture again. Many of Sky-tec's current starters offer kickback protection.

This condition is related to the starter drive extension and retraction and affects all styles of starters. If, during normal extension, the gear does not extend completely, stress will be placed on the drive gear. If the starter drive does not disengage after start, the engine will tend to drive the gear placing stress on the gear and destroying the motor. In either case, the gear will rapidly wear or fracture.

Sticking mechanical starter drives, e.g., Bendix drives, should be cleaned with mineral spirits and only lubricated with silicone spray. Oil or common greases should not be used as they will attract and retain dust and grit causing the starter drive to stick or wear rapidly. Solenoid-actuated starters do not require any type of cleaning or lubrication. If the starter is not going to be used for some period of time the shaft can be oiled to prevent corrosion.

There are two potential causes of this condition. If it is a mechanical starter drive (Bendix) and sticks intermittently, it most likely needs to be lubricated. This type of starter drive is initially lubricated to allow smooth operation. The drive gear must move in and out and also rotate. In use it can become dry and may begin to stick and fail to engage or disengage. We recommend lubricating this type of starter drive every fifty (50) hours of operation. The other likely factor for intermittent engagement would be a faulty starter contactor. If you want to check a contactor, it is best to do so with a load applied. Resistance in the contactor, even a fraction of an ohm, is enough to produce poor or no operation due to the high current field. In a 12-volt starting circuit drawing 60 amps, for example, the addition of 0.2 ohms of resistance due to an oxidized connector or carbonized contact may drop the current to the load to 36 amps. This is a 40-percent loss in starter operating power caused only by a 0.2-ohm resistance. Checking the circuit without a load would require that a lot of resistance be placed in line. The best method of checking the contactor is to disconnect the lead from the starter and connect it to a battery load-meter tester. Activate the contactor and check the voltage on each side of the contactor. A 0.1-volt drop is normal for a new or nearly new contactor. If you find any more than 0.3-volt drop, replace it.

This is normal for a permanent-magnet starter. Although power is removed by releasing the key/start button, a permanent-magnet motor will actually provide power to itself as it winds down and will keep the starter drive engaged for about a half-second until it loses sufficient RPM to fully disengage.

THIS CAN BE A DANGEROUS SITUATION. The starter contactors in many older aircraft may become welded shut after years of use. BE EXTREMELY CAREFUL. A starter contactor that is welded shut could cause the propeller to rotate when the master switch is energized, regardless of the position of the start button or switch. Replace the starter contactor. Your starter may have been damaged by this as well and may also need to be overhauled or replaced.

Lightweight starters do not have as much housing bulk surrounding them, so they aren’t as effective at insulating the gear train noise from the operator. To compound the issue, switching from a legacy heavyweight starter to a lightweight starter may also change the design style from a direct drive to a gear reduction drive in order to obtain the same drive torque. Gear-reduced starters have a much different noise signature than direct drive starters.

122 tooth gear rings have a "v" shape, whereas 149 tooth gear rings have a "u" shape. Be aware that just because your aircraft (or engine) is supposed to have a certain ring gear doesn't necessarily mean that it does. You should always confirm and order the correct starter to match.

It appears that Superior reverse engineered the 60882-type ring gear support assembly (for 122-tooth ring gears) when they manufactured and PMA certified Superior Ring Gear Support Assembly PN SL77579-1 Rev.11 (for 149-tooth ring gears). Unfortunately, when pairing those ring gear support assemblies with 149-tooth ring gears, the ring gear rests further aft than Lycoming specification and therefore tends to crash the front face of NL-type starters by a mere couple thousandths of an inch. Other starter models tend to stand back sufficiently from the ring gear, so the mismatch is not as problematic. Since the NL “hugs the line” defined by Lycoming, the mismatched ring gear and support assembly causes an interference condition.

Use a Lycoming alternator strap and MS20074-05-06 (5/16-18 thread) bolts.

The Kickback Protection System or KPS® for the NL and NL/EC family of starters is through a field-replaceable shear pin. When energizing the starter, if the pinion engages the flywheel and the starter motor spins (or at least sounds like it is spinning), but the starter’s pinion gear does not rotate you should replace the shear pin.