Product Details
MC600 Series Universal Solid Wire Vernier Mixture Control
Precise mixture control for less money!
- Minor alteration (requires logbook entry only)
- FAA-PMA approved for many Cessna, Piper, Beechcraft, Mooney, Maule and Stinson aircraft
- Fits most carbureted engines
- Teflon lined conduit for smooth, consistent operation
- Conduit is 1/4″ diameter
- Extra long – trim to exact length
Installation Tip:
The MC600 series mixture controls require a 3/4 inch instrument panel hole. Most aircraft have a 1/2 inch hole from the factory that must be enlarged before installation of an MC600 series mixture control. Use P/N 44460 for ease of installation.
Eligible Aircraft
| Make | Model | Start S/N | End S/N | Eligibility Chart |
|---|---|---|---|---|
| Beechcraft | 19A | MB-289 | MB-460 | 1404 |
| Beechcraft | A23-19 | MB-1 | MB-288 | 1404 |
| Beechcraft | B19 | MB-481 | MB-520 | 1404 |
| Beechcraft | M19A | MB-461 | MB-480 | 1404 |
| Beechcraft | B23 | M-1095 | M-1284 | 1404 |
Part Number Information
Additional product information
Approval: FAA PMA Modification Article
Frequently Asked Questions
I purchased a laser engraved knob and the thickness of the marking is very shallow. What kind of wear resistance can I expect?
The laser marking does not harm the hard durable anodize coating on the aluminum knob. The CO2 laser process only bleaches the color from the anodizing leaving a silver white color that contrasts with the surrounding dyed anodize. The durability of the laser marked area is not affected by the laser. Our tests have shown that the laser process actually improves the corrosion resistance of the anodize layer. The CO2 laser engraves aluminum knobs by vaporizing the surface leaving a deep durable groove. This groove is then filled with a special paint for contrast. The result is a durable long lasting mark.
Why is my new engine control too long/short?
There are several things that could be different such as engine/aircraft modifications, rigging/clocking of control arm or adjustment of rod end will be needed, placement of clamps or brackets may be different, or a previous installation change such as routing from original.
What is the minimum bend radius for my engine control?
McFarlane's Storage and Packaging Specification requires a specific packaging minimum radius based on the length of the control, type of wire used, and the configuration of the control end(s). Please contact us to determine the exact requirements for your specific control.
How do I trim my engine control to length?
Please reference the Installation Instructions included with your new control.
My Vernier-Assist Mixture control came apart during installation or maintenance. Can it be put back together?
Yes, please return the control to McFarlane for repair.
How do I clean and sanitize a McFarlane Push-Pull Control?
We make the following cleaning and sanitizing recommendations to be completed between flights: Recommended Cleaning Process 1. Put on clean disposable gloves prior to cleaning and disinfection. 2. Pull controls back to the fully retracted position to expose the full length of the control shafts. 3. Apply isopropyl alcohol to a clean microfiber towel. Do not spray any solution directly on the controls or any other surfaces or components in the aircraft. !!! WARNING: DO NOT USE BLEACH WIPES ON ANY MCFARLANE CONTROL !!! 4. Gently and thoroughly wipe down every control knob surface and control shaft. 5. Let cleaning solution dry on these surfaces (contact time). 6. Use a clean and dry microfiber cloth to wipe away any solution residue left on knob and control shaft surface. 7. Remove all gloves, towels, and cleaning supplies from the work area in the aircraft. Please contact McFarlane Sales directly at 866-920-2741 or 785-594-2741 or sales@mcfarlaneaviation.com if you have any additional questions regarding the disinfection of our controls.
